Expert Answers about Toyota T100 Pickup

Parts Needed For Towing a Jayco Jay Flight Travel Trailer With a 1998 Toyota T100 4X4 Pickup
For your 1998 Toyota T100 4X4 you are going to need a few parts to be able to pull the 2015-2018 Jayco Jay Flight camper that you are looking at. If your Toyota does not have a receiver that is where you will want to start. The Draw-Tite Max-Frame Trailer Hitch Receiver # 75144 is custom fit for your Toyota and requires no drilling to install it on the frame. For the wiring you will need the Tekonsha T-One Vehicle Wiring Harness # 118496 and a Universal Installation Kit # ETBC7 to attach...
view full answer...

Troubleshooting Lights Not Working on Camper Trailer
There are a number of reasons why many of the lights on your 2006 Fleetwood Niagara so in order to determine the specific problem you will need to use a circuit tester such as # PTW2993 to test the connector on your tow vehicle after disconnecting it from your trailer. Check the wiring going into your harness from your tail lights to see if those wires are carrying the correct signals, if not then the issue is with the vehicle wiring. If the signals going to your harness are okay, you'll...
view full answer...

Trailer Wiring Harness for a 1996 Toyota T-100
The wiring harness for your vehicle 1996 Toyota T-100 is sold separately. I recommend The T-One Vehicle Wiring Harness, part # 118496, for your vehicle. Click on the link below to see the installation instructions for the T-1 harness.
view full answer...

Backing Plate Recommendation for Wood Floor E-Track Trailer Installation
To use E-track on your aluminum framed, wood-floored trailer I would recommend using the backing plate part # BPEZ. This will mount underneath the wood and then would give the E-track like part # E19148 (5 foot section) a secure attachment.
view full answer...

Suspension Enhancement For 1993 Toyota T100 Itasca Spirit Motor Home
Yes the Timbren Rear Suspension Enhancement System Item # TDVR05091 is compatible with the 1993 Toyota T100 Itasca Spirit Motor Home
view full answer...

Adding a 7 Pole to my 1997 Toyota T100
Yes you can use the Curt T-Connector Vehicle Wiring Harness with 5-Pole Flat Trailer Connector part # C56513 to use as the basis for your 7 pole connector. Once this is installed I recommend cutting the connector off and using heat shrink butt connectors like part # DW05744-10 to connect to the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires part # ETBC7. This simply eliminates a connection that could eventually fail. At that point just...
view full answer...

Dimensions of Curt Trailer Hitch C13133
Attached are some photos of these dimensions for the Curt Trailer Hitch Receiver # C13133 that you referenced. Here is a list of the vehicles that this hitch fits: 2009 - 2017 Volkswagen Tiguan 2017 - 2018 Volkswagen Tiguan Limited
view full answer...

6 Pin Round Trailer Connector Adapter to 6-Pin Rectangle Connector on 2003 Skamper Popup Camper
It sounds like you are looking for the Hopkins Trailer Connector Adapter - 6-Pole Round to 6-Pole Square # HM47415. This adapter has an overall length of 10 inches.
view full answer...

Parts Needed to Flat Tow 1995 Toyota T100 Automatic Transmission
From the research I did on your vehicle the only way you could flat tow it is by disconnecting the driveshaft. We do not offer drive shaft disconnects but we do offer everything else needed to flat tow your vehicle. You'd need a base plate kit part # 1128-1 to provide the connection to the tow bar. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle. The most popular compatible tow bar is the...
view full answer...

How to Install Wiring Harness 118496 in 1995 Toyota T100
The installation of a 4-flat connector such as the T-One Vehicle Wiring Harness # 118496 in your 1995 Toyota T100 is a very simple and straightforward process; it only requires plugging in the T-connectors at the taillight wiring harness. I was unable to locate what harness you ordered from us so I'm not certain what exact harness you used but the process should not be any different (see linked installation video which shows how this harness installs). If you only cut off the connector...
view full answer...

How to Install a Brake Controller on a Toyota T100 Pickup
It is possible to install a brake controller on your 1998 Toyota T100 pickup, but there are no custom fit wiring adapters available for that truck. The plug you found under the dash is probably not for a brake controller, but you could test the pins for power to be sure. One pin should have constant 12 volt power and one pin should only have power when the brake pedal is pressed. The other two pins should not have power at all. From the information we have, a brake controller must be hardwired...
view full answer...

Will the Carr C-Profile Rota Light Mounting Bar Part # CARR210111 Fit a 1997 Toyota T100
The Carr C-Profile Rota Light Mounting Bar part # CARR210111 is confirmed to fit your 1997 Toyota T100 and will work well with a curved 50" light bar. A 50" light bar is the maximum length that can BE installed using this roof mount. For a curved 50" light bar compatible with this bracket I recommend using the Putco High Power Luminix Curved Off-Road Light Bar part # P10055. As a curved light bar is much more expensive than a straight light bar. A more cost effective solution for you...
view full answer...

Could Yakima Round Bar Roof Rack Fit into Rola Roof Track 59855
Yes, you can fit Yakima round bar roof racks into the Rola tracks you mentioned. The track dimensions of this are the same as what Yakima roof rack components require. To do that you will need 4 of the Yakima Control Towers # Y8890027, 2 sets of the Yakima Landing Pad # Y00221, and one set of Yakima Crossbars. For 58 inch bars you can use # Y00409, for 66 in bars use # Y00410, or for 78 inch bars you can use # Y00411.
view full answer...

Availability Of A Trailer Hitch For A 1996 Toyota T100 Pickup
We do carry a trailer hitch for the 1996 Toyota T100 pickup. The hitch you are looking for it the Curt # C76VV. This is a class 3 hitch with a 2" receiver and is rated for 5,000 lbs towing. Our site has it listed under "1996 Toyota T100" Instead of "1996 Toyota T100 pickup". I have confirmed with Curt that this is made for all models of the 1996 T100 provided it is a 4 wheel drive model.
view full answer...

Does TorkLift GlowStep Camper Scissor Steps Come with Mounting Bracket
Hey Pat, yes the TorkLift GlowStep Camper Scissor Steps w/ Landing Gear # TLA7506-8000 do come with the needed mounting bracket.
view full answer...

Fifth Wheel Hitch and Rail Kit Recommendation for 1996 Toyota T100
For your 1996 Toyota T100 truck you would need a slider hitch to allow you to make tight turns without truck cab interference. For that the best option is the Demco Auto slide part # DM8550034 which will automatically slide as you make tight turns. You will need the separate fifth wheel rail kit to go with it as well which is part # DM8552009-71. There will be drilling into the frame and bed as well.
view full answer...

Drawtite Hitch Receiver for 1993 Toyota T100 4X4
It is not recommended to attach this to your 1993 Toyota T100 4X4 pickup without the bumper. If you don't do the installation completely then you won't have the weight capacity of 5,000 lbs maximum gross trailer weight and 500 lbs maximum tongue weight. I have linked a couple of pictures and an installation video of the Draw-Tite Max-Frame Trailer Hitch Receiver item # 75144 being installed on a 1993 Toyota T100 pickup. The hitch is attached by six bolts to the frame and 2 bolts to the bumper.
view full answer...

Troubleshooting Faint Right Stop/Turn Blinker Circuit of Trailer Wiring
Most likely your trailer's ground is insufficient to power that circuit or the power draw from that circuit is too much for your vehicle to support it. I'd be willing to bet it's the ground circuit of either your trailer's wiring or the truck's wiring. Try improving the connection from the ground strap of your trailer wiring and also if you are using a 4-way to 7-way adapter make sure it's ground strap is connected to a clean metal surface.
view full answer...

Recommended 5th Wheel Base Rails for 1995 Toyota T100 Pickup
The correct replacement installation hardware and bracket kit for your Reese 10 bolt rails is the part # RP30439. This kit is intended for the Universal Base Rails # RP30035. With this in mind, the Reese Universal Base Rail - 10 Bolt Kit is actually not confirmed to fit your 1995 Toyota T100. For 5th Wheel Base Rails that are confirmed to fit, I instead recommend looking at the Demco Rails # DM8552009-71. This kit will include the base rails, brackets and all the hardware needed for installation....
view full answer...

How to Troubleshoot Turn Signals on Trailer Not Working
The # 33355 trailer wiring harness you purchased receives its ground connection from its connection to the vehicle, it doesn't need a separate ground connection. The easiest way to test the harness would be to try plugging another trailer into the vehicle, then try another vehicle with the trailer. This will immediately tell you where the problem lies. If this isn't possible, I'll walk you through some troubleshooting strategies. When you have trailer lights acting up, the first thing...
view full answer...